Simple Buzzer Circuit Diagram

Hi friends today I'm going to give you a simple buzzer circuit diagram.This circuit operates with IC NE 555 .And also this circuit can be operated with 5V to 15V. By changing the variable resistor you can change the frequency.

Note:
# To get good result use 8 Ohm speakers.
# Build this circuit on a P.C.B

Simple touch sensitive circuit diagram

Most of the people requested touch sensitive circuit diagrams from FREE CIRCUIT DIAGRAMS 4U .So today we hope to give you a touch sensitive circuit diagram.Here we have used NE555 IC.This circuit can be operated with 6V power.Removing the led you can attach a relay for the circuit.

Note:     # Build this circuit on a pcb   
             # Don't supply over 6V

Simple 555 Timer circuit diagram

A lot of guys requested a simple timer circuit so this is the circuit.This circuit runs with main IC NE555. you can change the frequencies of the circuit by changing the values of R1, R2,C .This circuit runs with 4.5V.

NE 555 Pulse generator

Most of our members asked pulse generator circuits. so this is a simple and common circuit.and you can use this with your light circuit diagrams too.

555 DC to AC inverter circuit diagram

This is inverter circuit diagram.Here I have used famous Transistors TIP41 and TIP42.And the frequency is generated by NE555.By using R4 you can control the frequency.out put voltage is 120V-230V.the frequency is 50Hz.This circuit operates with 5V-15V.

Pulse Generator With NE 555

Most of time we have to use pulse generators.Here I have introduce a Pulse generator with NE555 IC.Normally we use this IC with lots of circuits.When you operate this circuit give 5v as the supply voltage because this IC works with that current But don't give more than 5v.




Note

If you want to know how you can attach this circuit with other circuits just see knight rider circuit

555 Timer as Monostable Multivibrator

A monostable multivibrator (MMV) often called a one-shot multivibrator, is a pulse generator circuit in which the duration of the pulse is determined by the R-C network,connected externally to the 555 timer. In such a vibrator, one state of output is stable while the other is quasi-stable (unstable). For auto-triggering of output from quasi-stable state to stable state energy is stored by an externally connected capaci­tor C to a reference level. The time taken in storage determines the pulse width. The transition of output from stable state to quasi-stable state is accom­plished by external triggering. The schematic of a 555 timer in monostable mode of operation is shown in figure.


Pin 1 is grounded. Trigger input is applied to pin 2. In quiescent condition of output this input is kept at + VCC. To obtain transition of output from stable state to quasi-stable state, a negative-going pulse of narrow width (a width smaller than expected pulse width of output waveform) and amplitude of greater than + 2/3 VCC is applied to pin 2. Output is taken from pin 3. Pin 4 is usually connected to + VCC to avoid accidental reset. Pin 5 is grounded through a 0.01 u F capacitor to avoid noise problem. Pin 6 (threshold) is shorted to pin 7. A resistor RA is connected between pins 6 and 8. At pins 7 a discharge capacitor is connected while pin 8 is connected to supply VCC.


555 IC Monostable Multivibrator Operation.






555 monostable-multivibrator-operation

For explain­ing the operation of timer 555 as a monostable multivibrator, necessary in­ternal circuitry with external connections are shown in figure.
The operation of the circuit is ex­plained below:

Initially, when the output at pin 3 is low i.e. the circuit is in a stable state, the transistor is on and capacitor- C is shorted to ground. When a negative pulse is applied to pin 2, the trigger input falls below +1/3 VCC, the output of comparator goes high which resets the flip-flop and consequently the transistor turns off and the output at pin 3 goes high. This is the transition of the output from stable to quasi-stable state, as shown in figure. As the discharge transistor is cut­off, the capacitor C begins charging toward +VCC through resistance RA with a time constant equal to RAC. When the increasing capacitor voltage becomes slightly greater than +2/3 VCC, the output of comparator 1 goes high, which sets the flip-flop. The transistor goes to saturation, thereby discharging the capacitor C and the output of the timer goes low, as illustrated in figure.

Thus the output returns back to stable state from quasi-stable state.

The output of the Monostable Multivibrator remains low until a trigger pulse is again applied. Then the cycle repeats. Trigger input, output voltage and capacitor voltage waveforms are shown in figure.
Monostable Multivibrator Design Using 555 timer IC

The capacitor C has to charge through resistance RA. The larger the time constant RAC, the longer it takes for the capacitor voltage to reach +2/3VCC.

In other words, the RC time constant controls the width of the output pulse. The time during which the timer output remains high is given as

tp = 1.0986 RAC
where RA is in ohms and C is in farads. The above relation is derived as below. Voltage across the capacitor at any instant during charging period is given as

vc = VCC (1- e-t/RAC)

Substituting vc = 2/3 VCC in above equation we get the time taken by the capacitor to charge from 0 to +2/3VCC.

So +2/3VCC. = VCC. (1 – e-t/RAC) or t – RAC loge 3 = 1.0986 RAC

So pulse width, tP = 1.0986 RAC s 1.1 RAC

The pulse width of the circuit may range from micro-seconds to many seconds. This circuit is widely used in industry for many different timing applications.