Free Electronic Circuits,Schematic Diagram,Circuit Diagrams

Thumbnail image that says sleek button using photoshop that links to a Photoshop tutoril. free, electronic circuit, circuit diagram, circuit schematic, schematic diagram, electronic diagram, audio, amplifier, power supply, guitar effect, current loop, current limiter, video, receiver, transmitter, transceiver, transistor, radio frequency, rf, active filters, digital, analog circuit, pwm, micro controller Free download

Free Electronic Circuits,Schematic Diagram,Circuit Diagrams

External links - Jqueryelectronics circuit,circuits,schematic diagram,circuit design,circuit diagram, circuit

Electronic Circuit,Schematic Diagram,Circuit Diagrams

External links - Jqueryelectronic circuit, circuit diagram, circuit schematic, schematic diagram, electronic diagram, audio, amplifier, power supply, guitar effect, current loop, current limiter, video, receiver, transmitter, transceiver, transistor, radio frequency, rf, active filters, digital, analog circuit, pwm, micro controller Free download

Best Song Lyrics Collection

External links - JqueryFind The Music Lyrics To Any Song! It's Free DAILY UPDATED! One of the largest,most accurate, browsable and searchable song lyrics source on the net. lyric, lyrics, song, music, song lyrics, music lyrics

Tuesday, September 01, 2009

Car Subwoofer Driver


This unit is intended to be connected to an existing car stereo amplifier, adding the often required extra "punch" to the music by driving a subwoofer. As very low frequencies are omnidirectional, a single amplifier is necessary to drive this dedicated loudspeaker.The power amplifier used is a good and cheap BTL (Bridge Tied Load) 13 pin IC made by Philips (now NXP Semiconductors) requiring a very low parts count and capable of delivering about 22W into a 4 Ohm load at the standard car battery voltage of 14.4V.








Car Subwoofer Driver




Parts:

P1_____________10K Log Potentiometer
P2_____________22K Dual gang Linear Potentiometer

R1,R4___________1K 1/4W Resistors
R2,R3,R5,R6____10K 1/4W Resistors
R7,R8_________100K 1/4W Resistors
R9,R10,R13_____47K 1/4W Resistors
R11,R12________15K 1/4W Resistors
R14,R15,R17____47K 1/4W Resistors
R16_____________6K8 1/4W Resistor
R18_____________1K5 1/4W Resistor

C1,C2,C3,C6_____4µ7 25V Electrolytic Capacitors
C4,C5__________68nF 63V Polyester Capacitors
C7_____________33nF 63V Polyester Capacitor
C8,C9_________220µF 25V Electrolytic Capacitors
C10___________470nF 63V Polyester Capacitor
C11___________100nF 63V Polyester Capacitor
C12__________2200µF 25V Electrolytic Capacitor

D1______________LED any color and type

Q1,Q2_________BC547 45V 100mA NPN Transistors

IC1___________TL072 Dual BIFET Op-Amp
IC2_________TDA1516BQ 24W BTL Car Radio Power Amplifier IC

SW1____________DPDT toggle or slide Switch
SW2____________SPST toggle or slide Switch capable of withstanding
a current of at least 3A

J1,J2__________RCA audio input sockets

SPKR___________4 Ohm Woofer or two 8 Ohm Woofers wired in parallel





The stereo signals coming from the line outputs of the car radio amplifier are mixed at the input and, after the Level Control, the signal enters the buffer IC1A and can be phase reversed by means of SW1. This control can be useful to allow the subwoofer to be in phase with the loudspeakers of the existing car radio.
Then, a 12dB/octave variable frequency Low Pass filter built around IC1B, Q1 and related components follows, allowing to adjust precisely the low pass frequency from 70 to 150Hz.
Q2, R17 and C9 form a simple dc voltage stabilizer for the input and filter circuitry, useful to avoid positive rail interaction from the power amplifier to low level sections.


Notes:


* IC2 must be mounted on a suitable finned heatsink
* Due to the long time constant set by R17 and C9 in the dc voltage stabilizer, the whole amplifier will become fully operative about 15 - 30 sec. after switch-on.

Technical data:

Output power (1KHz sinewave):
22W RMS into 4 Ohms at 14.4V supply
Sensitivity:
250mV input for full output
Frequency response:
20Hz to 70Hz -3dB with the cursor of P2 fully rotated towards R12
20Hz to 150Hz -3dB with the cursor of P2 fully rotated towards R11
Total harmonic distortion:
17W RMS: 0.5% 22W RMS: 10%



1 Comment:

Wahyu Eko said...

Very interesting electronics site , nice job sir.

Discover your circuit you need here about thousand circuit Circuit Schematic Electronics

Post a Comment | Feed

Post a Comment



.
.
.
.
.
 
TopBlogDir.blogspot.com button Top Blogs Technology Blogs Technology Blogs Add to My Yahoo! On our way to 1,000,000 rss feeds - millionrss.com Blog Search Blog Directory & Search engine LocalSubmit.com : search engine submissions and website promotion with free advice TopOfBlogs SonicRun.com blog search directory Submit your website to 20 Search Engines - FREE with ineedhits! Download Juice, the cross-platform podcast receiver
Today.com SoMuch.com: Internet Links Directory NZPAGES - Your New Zealand Web Site Directory BlogRankers.com Make Money Blogging

Search Optimization, Search Engine Optimization

A link

El directorio y buscador de Mexico Blog Search Engine Top Blogs http://www.freesearchenginesubmission.infovisiter ici Cheap Hotels Online blog directory ping fast  my blog, website, or RSS feed for Free Green-Tech blog
State Your Blog - Blog Top Sites - www.stateyourblog.com
http://www.freedomain.co.nr Increase Page Rank Cyndi's List of Genealogy Sites
 on the Internet Cyndi's List of Genealogy Sites on the Internet Search Engine Submission - AddMe http://www.freesearchenginesubmission.infoclic pour info Search Engine Marketing and Optimization

Thank U & Come Again.....


Search Engine Optimization and SEO Tools
Submit ExpressSearch Engine Marketing

FREE CIRCUIT DIAGRAMS 4U Copyright © 2009 REDHAT Dashboard Designed by SAER