Free Electronic Circuits,Schematic Diagram,Circuit Diagrams

Thumbnail image that says sleek button using photoshop that links to a Photoshop tutoril. free, electronic circuit, circuit diagram, circuit schematic, schematic diagram, electronic diagram, audio, amplifier, power supply, guitar effect, current loop, current limiter, video, receiver, transmitter, transceiver, transistor, radio frequency, rf, active filters, digital, analog circuit, pwm, micro controller Free download

Free Electronic Circuits,Schematic Diagram,Circuit Diagrams

External links - Jqueryelectronics circuit,circuits,schematic diagram,circuit design,circuit diagram, circuit

Electronic Circuit,Schematic Diagram,Circuit Diagrams

External links - Jqueryelectronic circuit, circuit diagram, circuit schematic, schematic diagram, electronic diagram, audio, amplifier, power supply, guitar effect, current loop, current limiter, video, receiver, transmitter, transceiver, transistor, radio frequency, rf, active filters, digital, analog circuit, pwm, micro controller Free download

Best Song Lyrics Collection

External links - JqueryFind The Music Lyrics To Any Song! It's Free DAILY UPDATED! One of the largest,most accurate, browsable and searchable song lyrics source on the net. lyric, lyrics, song, music, song lyrics, music lyrics

Saturday, August 29, 2009

Infra-red Level Detector

This circuit is useful in liquids level or proximity detection. It operates detecting the distance from the target by reflection of an infra-red beam. It can safely detect the level of a liquid in a tank without any contact with the liquid itself. The device's range can be set from a couple of cm. to about 50 cm. by means of a trimmer.Range can vary, depending on infra-red transmitting and receiving LEDs used and is mostly affected by the color of the reflecting surface. Black surfaces lower greatly the device's sensitivity.




Level Detector



Parts:


R1_____________10K 1/4W Resistor
R2,R5,R6,R9_____1K 1/4W Resistors
R3_____________33R 1/4W Resistor
R4,R8___________1M 1/4W Resistors
R7_____________10K Trimmer Cermet
R10____________22K 1/4W Resistor


C1,C4___________1µF 63V Electrolytic or Polyester Capacitors
C2_____________47pF 63V Ceramic Capacitor
C3,C5,C6______100µF 25V Electrolytic Capacitors

D1_____________Infra-red LED
D2_____________Infra-red Photo Diode (see Notes)
D3,D4________1N4148 75V 150mA Diode
D5______________LED (Any color and size)
D6,D7________1N4002 100V 1A Diodes

Q1____________BC327 45V 800mA PNP Transistor

IC1_____________555 Timer IC
IC2___________LM358 Low Power Dual Op-amp
IC3____________7812 12V 1A Positive voltage regulator IC

RL1____________Relay with SPDT 2A @ 220V switch
Coil Voltage 12V. Coil resistance 200-300 Ohm

J1_____________Two ways output socket





IC1 forms an oscillator driving the infra-red LED by means of 0.8mSec. pulses at 120Hz frequency and about 300mA peak current. D1 & D2 are placed facing the target on the same line, a couple of centimeters apart, on a short breadboard strip. D2 picks-up the infra-red beam generated by D1 and reflected by the surface placed in front of it. The signal is amplified by IC2A and peak detected by D4 & C4. Diode D3, with R5 & R6, compensates for the forward diode drop of D4. A DC voltage proportional to the distance of the reflecting object and D1 & D2 feeds the inverting input of the voltage comparator IC2B. This comparator switches on and off the LED and the optional relay via Q1, comparing its input voltage to the reference voltage at its non-inverting input set by the Trimmer R7.


Notes:

* Power supply must be regulated (hence the use of IC3) for precise reference voltage. The circuit can be fed by a commercial wall plug-in adapter, having a DC output voltage in the range 12-24V.
* Current drawing: LED off 40mA; LED and Relay on 70mA @ 12V DC supply.
* R10, C6, Q1, D6, D7, RL1 and J1 can be omitted if relay operation is not required.
* The infra-red Photo Diode D2, should be of the type incorporating an optical sunlight filter: these components appear in black plastic cases. Some of them resemble TO92 transistors: in this case, please note that the sensitive surface is the curved, not the flat one.
* Avoid sun or artificial light hitting directly D1 & D2.
* Usually D1-D2 optimum distance lies in the range 1.5-3 cm.

0 comments:

Post a Comment | Feed

Post a Comment



.
.
.
.
.
 
TopBlogDir.blogspot.com button Top Blogs Technology Blogs Technology Blogs Add to My Yahoo! On our way to 1,000,000 rss feeds - millionrss.com Blog Search Blog Directory & Search engine LocalSubmit.com : search engine submissions and website promotion with free advice TopOfBlogs SonicRun.com blog search directory Submit your website to 20 Search Engines - FREE with ineedhits! Download Juice, the cross-platform podcast receiver
Today.com SoMuch.com: Internet Links Directory NZPAGES - Your New Zealand Web Site Directory BlogRankers.com Make Money Blogging

Search Optimization, Search Engine Optimization

A link

El directorio y buscador de Mexico Blog Search Engine Top Blogs http://www.freesearchenginesubmission.infovisiter ici Cheap Hotels Online blog directory ping fast  my blog, website, or RSS feed for Free Green-Tech blog
State Your Blog - Blog Top Sites - www.stateyourblog.com
http://www.freedomain.co.nr Increase Page Rank Cyndi's List of Genealogy Sites
 on the Internet Cyndi's List of Genealogy Sites on the Internet Search Engine Submission - AddMe http://www.freesearchenginesubmission.infoclic pour info Search Engine Marketing and Optimization

Thank U & Come Again.....


Search Engine Optimization and SEO Tools
Submit ExpressSearch Engine Marketing

FREE CIRCUIT DIAGRAMS 4U Copyright © 2009 REDHAT Dashboard Designed by SAER