FREE CIRCUIT DIAGRAMS 4U: Electronic Candle Blow Out

Free Electronic Circuits,Schematic Diagram,Circuit Diagrams

Thumbnail image that says sleek button using photoshop that links to a Photoshop tutoril.

free, electronic circuit, circuit diagram, circuit schematic, schematic diagram, electronic diagram, audio, amplifier, power supply, guitar effect, current loop, current limiter, video, receiver, transmitter, transceiver, transistor, radio frequency, rf, active filters, digital, analog circuit, pwm, micro controller Free download

Electronic Circuit,Schematic Diagram,Circuit Diagrams

electronic circuit, circuit diagram, circuit schematic, schematic diagram, electronic diagram, audio, amplifier, power supply, guitar effect, current loop, current limiter, video, receiver, transmitter, transceiver, transistor, radio frequency, rf, active filters, digital, analog circuit, pwm, micro controller Free download

Monday, August 24, 2009

Electronic Candle Blow Out

This design was developed by request of a correspondent having made a sort of LED candle and needing to switch off the LED with a puff.This simple, easy to build gadget can be useful as a prop for Halloween and Christmas season, shows and the like.

Audio Clipping Indicator

Parts:
R1______________10K 1/4W Resistor
R2_______________1M 1/4W Resistor
R3_______________1K 1/4W Resistor
R4_______________4K7 1/4W Resistor (See Notes)
R5______________10K 1/4W Resistor (See Notes)
R6_____________100R 1/4W Resistor (See Notes)
C1_____________100pF 63V Ceramic Capacitor
C2______________10µF 25V Electrolytic Capacitor
C3_____________100nF 63V Polyester or Ceramic Capacitor D1___________1N4148 75V 150mA Diode
D2______________LED (Any suitable type)
Q1____________BC550C 45V 100mA Low noise High gain NPN Transistor Q2____________BC337 45V 800mA NPN Transistor
Q3____________BC327 45V 800mA PNP Transistor
MIC1__________Miniature electret microphone
P1_____________SPST Pushbutton Switch
B1_______________3V Battery (2 x 1.5V AA, AAA Cells in series etc.)

Q2 & Q3 form a self-latching pair that start operating when P1 is pushed: in this way the LED (or bulb) will illuminate steadily. When someone emits a strong puff in the vicinity of the small electret microphone, the resulting signal will be greatly amplified by Q1 and a rather long positive pulse (shaped by D1 and C2) will reset the self latching pair through the Emitter of Q2. The very low (and unusual) value of C1 acts as a simple high-pass filter, in order to prevent that normal speech or environmental noise shut off the device. Obviously, such a simple filter cannot be very discriminating, therefore, not only a strong puff will reset the circuit but also a loud shout, blow, clap or stroke. Notes: * A small bulb can be used in place of the LED. In this case a 3 - 3.5V, 0.7W (200mA) incandescent bulb can be used satisfactorily. Therefore, D2, R5 and R6 must be omitted, the bulb wired in place of R5 and R4 value changed to 1K5. * Using a bulb instead of the LED, a 1.5V battery supply could also be used. A 1.5V, 0.3A incandescent bulb will work, but R4 must be replaced by a 470 Ohm Trimmer, adjusted to allow a reliable circuit operation. * Please note that the circuit will draw a small current even when the LED or bulb are off. This current is about 1.2mA for the LED version of the circuit, 1.5mA for the 3V bulb version and 1mA for the 1.5V bulb version. Therefore, in some circumstances, the addition of a power on-off switch could be necessary.